TYPE I EMULSIFIED ASPHALT SLURRY SEAL

  • TYPE I EMULSIFIED ASPHALT SLURRY SEAL SURFACE TREATMENT

    asphalt emulsion slurry seal on the dense graded asphalt surfaces of Runway 3/21 and the Taxiway/Apron as shown in Figure 2 attached hereto. The slurry seal shall consist of a mixture of an approved emulsified asphalt, mineral aggregate, water and

  • Slurry Seal

    Slurry Seal shall consist of mixing asphalt emulsion, aggregate, and water and spreading the mixture on a surfacing or pavement where shown on the plans, as specified in these specifications and the special provisions, and as directed by

  • Slurry Seal Treatment Types

    A slurry seal is the application of a mixture of water, asphalt emulsion, aggregate (very small crushed rock), and additives to an existing asphalt pavement surface. A slurry seal is similar to a fog seal except the slurry seal has aggregates as part of the mixture.

  • Slurry Seals | Pavement Interactive

    Slurry Seals. A slurry seal is a homogenous mixture of emulsified asphalt, water, well-graded fine aggregate and mineral filler that has a creamy fluid-like appearance when applied. Slurry seals are used to fill existing pavement surface defects as either a preparatory treatment for other maintenance treatments or as a wearing course.

  • For Emulsified Asphalt Slurry Seal

    experience in designing Emulsified Asphalt Slurry Seal Surfacing. equipped to self-load materials while continuing to apply slurry seal. Either type machine shall

  • Latex Modified Black Rock Slurry Seal Type II & III

    2.01 SCOPE AND PURPOSE. Slurry Seal shall consist of mixing asphalt emulsion, aggregate, and water and spreading the mixture on

  • Section 427 Emulsified Asphalt Slurry Seal

    Emulsified asphalt slurry seal is used to seal small cracks and correct moderate surface condition. Apply this type at a rate of 10 to 20 lbs/yd² (5.5 to 11 kg/m²) based on dry aggregate weight. If more than 20 lbs/yd² (11 kg/m²) of emulsified asphalt slurry seal is required, apply additional lifts of the same mixture.

  • SLURRY SEAL SPECIFICATIONS – (1%, 3% Latex

    SLURRY SEAL SPECIFICATIONS emulsion shall be pumpable and suitable for use in a Slurry Seal machine. The emulsified asphalt shall conform to the type

  • Chapter 8 Slurry Seals - Caltrans

    for Emulsified Asphalt Slurry Seal Type III Min Type III Max Chapter 8 – Slurry Seals. • Plot sand adhesion versus emulsion content Chapter 8 – Slurry

  • SECTION 02505 EMULSIFIED ASPHALT SLURRY SEAL

    SECTION 02505 EMULSIFIED ASPHALT SLURRY SEAL PART 1 GENERAL amount and type of asphalt emulsion to be blended with aggregate shall be determined by the

  • SECTION 02505 EMULSIFIED ASPHALT SLURRY SEAL

    A. The slurry seal shall consist of a mixture of an approved emulsified asphalt, mineral aggregate, water and specified additives, proportioned, mixed and uniformly spread over a properly prepared surface. The completed slurry seal shall leave a homogeneous mat, adhere firmly to the prepared

  • Type II Emulsified Asphalt Slurry Seal Surfacing | City of

    Slurry Seal. The City of Tualatin is requesting price quotes for Slurry Seal of multiple residential streets. The project consists of applying a mixture of Type II Emulsified Asphalt Slurry Seal Surfacing in accordance with Section 00706 of the 2015 Oregon Department of Transportation (ODOT) Standard Specifications.

  • S4500 Slurry Seal - Woodburn

    A. Slurry seal shall consist of a mixture of an approved emulsified asphalt, mineral aggregate, water and specified additives, proportioned, mixed and uniformly spread over a properly prepared surface as directed by the Engineer. B. The completed slurry seal shall leave a homogenous mat, adhere firmly to the prepared surface,

  • Section 427 Emulsified Asphalt Slurry Seal

    Emulsified asphalt slurry seal is used to seal small cracks and correct moderate surface condition. Apply this type at a rate of 10 to 20 lbs/yd² (5.5 to 11 kg/m²) based on dry aggregate weight. If more than 20 lbs/yd² (11 kg/m²) of emulsified asphalt slurry seal is required, apply additional lifts of the same mixture.

  • Slurry Seal Emulsion - Graniterock

    A slurry seal is a mixture of well-graded fine aggregate, mineral filler (if needed), emulsified asphalt, and water applied to a pavement as a surface treatment. It is used in both the preventive and corrective maintenance of asphalt pavement surfaces.

  • Recommended Performance Guidelines

    Each load of emulsified asphalt shall be accompanied with a Certificate of Analysis/ Compliance to assure that it is the same as that used in the mix design. 4.2 AGGREGATE 4.2.1 GENERAL The mineral aggregate used shall be the type and grade specified for the particular use of the slurry seal.

  • Slurry Seal Overview - California Pavement

    Slurry Seal Overview. Slurry seal Slurry seal is a mixture of emulsified asphalt, Shown below are the materials and percent quantities for a Type I slurry seal:

  • SPECIAL SPECIFICATION 3250 Emulsified Asphalt Slurry Seal

    Furnish and place an emulsified asphalt slurry seal surface treatment. consisting of a mixture of emulsified asphalt, mineral aggregate, and water properly. proportioned and mixed on an asphalt prepared underlying course in accordance with the. details shown on the plans and the requirements of this item.

  • Asphalt Preservation Benefits with Slurry Seal and

    Asphalt Preservation Benefits with Slurry Seal and Micro - Fahrner Asphalt Sealers, LLC - 35+ years of Pavement Maintenance and

  • Slurry Seal Surfacing | Hardrives Construction

    Durability and Economy make Slurry Seals a Great Option in Asphalt Maintenance. Slurry seals provide a new Type I slurry contains 1/8 of emulsion oils